Catalogue values for High Mast Lighting Tower for large area with LED Flood Lighting System
| Category | Specification | Bid Requirement (Allowed Values) |
|---|---|---|
| GENERIC | Height of High Mast Tower (in Meters) | |
| Installation and commissioning (Installation and commissioning work at multiple locations shall follow as per the guidelines of State/Central Govt rules and regulations as applicable) | ||
| Onsite warranty (in Years) | ||
| High mast System | No of sections | |
| Effective length of each section (in m) | ||
| Material construction: The mast shall be manufactured using special steel plates, conforming to | ||
| Bottom diameter (in mm) - Minimum | ||
| Plate thickness for Middle (in mm) - Minimum | ||
| Plate thickness for Bottom (in mm) - Minimum | ||
| No of longitudinal welds / section (in Nos) | ||
| Diameter of base plate (in mm) - Minimum | ||
| Thickness of base plate (in mm) - Minimum | ||
| Wind Load | Maximum Wind load | |
| Door Opening | Size of opening and closing door at base compartment of high mast (in mm) - Minimum | |
| Junction Box | Ingress protection for Junction Box i.e. IP Class (as per IS/IEC:60529:2001 latest) Test Report from Central Government lab/NABL/ILAC accrediated lab and report shall furnish to buyer on demand | |
| No of core | ||
| Cable category | ||
| Size of cable (in Sq mm) | ||
| Conductor material shall be | ||
| Winch | The winch shall have provision for manual operation in case of failure of the motor | |
| Stainless Steel Wire Rope | The breaking load of each rope shall be at full load as per the relevant standard | |
| Electrical System, Cable and Cable Connections | No. of cores | |
| Cable shall be | ||
| Conudctor material shall be | ||
| Cable Category | ||
| Incoming power cable from feeder panel to base compartment of mast and cable shall conforming to | ||
| Feeder pillar Panel | Feeder pillar panel for each mast | |
| Feeder panel shall be suitable for | ||
| The control panels shall be | ||
| Ingress protection for feeder pillar panel i.e IP Class (as per IS/IEC:60529:2001 latest).Test Report shall furnish from Central Government lab/NABL/ILAC accrediated lab to buyer on demand | ||
| It shall be fabricated out of | ||
| Thickness of sheet (in mm) | ||
| The panels shall be given pre-treatment and powder coated and color shall be | ||
| The stand shall be painted in | ||
| Cable entry shall be at the | ||
| The panels shall have | ||
| Laminated circuit diagram shall be pasted | ||
| Feeder pillar shall have pad locking arrangement | ||
| Earth terminal | ||
| Panel shall have a sloping cover to avoid accumulation of dust | ||
| Panel shall be provided with incoming & outgoing MCCB / MCB of appropriate rating and in desired quantity depending on total no of circuits in use | ||
| Timer for automatic ON & OFF of lights with pilot lamps shall be provided | ||
| Bus bars material | ||
| No of Cores | ||
| Size of cable (in Sq.mm) | ||
| Cable Shall be | ||
| The conductor material shall be | ||
| cable category | ||
| LED FLOOD LIGHT LUMINAIRE | No. of Luminaires for each high mast lighting tower (in Nos) | |
| LED Rating/System Wattage/Rated Power for each luminaire | ||
| Luminaire System Efficacy (Lumen/watt) | ||
| Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest | ||
| Mounting brackets (included) | ||
| Input operating Voltage range and frequency | ||
| Rated voltage | ||
| Colour temperature | ||
| Optic lense material (UV stabilised) (Write NA for without optic lense supply) | ||
| Operating temperature range | ||
| The luminaire shall be protected against surges and transients( Internal) | ||
| Number of electronic control gear per luminaire (power supplies) | ||
| Length of ISI marked three core wire (shall be provided along with supply of material) | ||
© 2025 GeM All rights reserved
Site operated and maintained by Managed Service Provider
New on GeM
