Catalogue values for Bunk Beds as per IS 17636
| Category | Specification | Bid Requirement (Allowed Values) |
|---|---|---|
| Generic Parameters | Type of bunk beds | 2 – Tier bunk beds (Fixed) |
| Railing / guard rail at upper bed | Fixed, Foldable, Detachable | |
| Tail board | With, Without | |
| Shape of tail board | Rectangular, Semi Circular, N.A | |
| Head rest | With | |
| Shape of headrest | Rectangular, Semi circular, N.A | |
| Provision for mosquito net holding rod | Fixed, Detachable, No mosquito net holding rod | |
| Position of ladder | From length side of bed | |
| Components assembly | With screws, bolt and washer | |
| Type of welding | MIG (Metal inert gas - Gas Metal Arc Welding) | |
| Provision of mattress panel | With | |
| Support member (jointed with frame) for mattress panel | Widthwise | |
| Number of Support panels for mattress | 3, 4, 5 Or higher | |
| Mode of supply | Knocked Down - To Be Assembled At Consignee Site By The Seller | |
| Type of Surface upholstery | NA | |
| Dimensions | Bed Dimensions (Length x Width) (±5 mm) | Adult (1910 mm x 965 mm), Two Adults (1910 mm x 1475 mm), Child and Adult (1910 mm x 1220 mm), Grown Up (1650 mm x 840 mm), Grown Ups (1650 mm x 1270 mm), Infant (1120 mm x 680 mm) |
| Height of entire structure (±5 mm) – excluding Mosquito net holding rods (minimum ceiling clearance to be 760 mm) | 1600.0, 1775.0, 1800.0 | |
| Height of lower tier (±5 mm) (Buyer should be careful while selecting keeping in mind minimum ceiling clearance as required ideally 760 mm minimum) | 405, 440, 460, 500 | |
| Guard rail height (± 5 mm) (The distance between the upper edge of the safety barriers and the upper side of the bed base) | 260.0 Or higher | |
| Gap between beds (clear distance between the upper and lower bed bases in mm) (± 5 mm) | 915, 1000, 1067 Or higher | |
| Gap between steps/treads (clear distance between two successive treads of ladder in mm) (± 5 mm) | 300.0 | |
| Number of steps/treads in ladder | 3 | |
| Usable width of ladder tread in mm (± 5 mm) | 300.0 | |
| Construction | Structure of metal bed frame including legs and head / tails / railing /supporting structure | MS hollow box rectangular or square sections, CRCA hollow box rectangular or square sections |
| Vertical leg structure sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 38.1 mm X 38.1 mm with 1.6 mm wall thickness | |
| Supporting structure of horizontals sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 50 mm X 25 mm with 1.2 mm wall thickness | |
| Other joining horizontal structure sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 25 mm X 25 mm with 1.2 mm wall thickness | |
| Stair rail sections for upper level (tolerance ± 2 mm excluding wall thickness) | Tube of size 25 mm X 25 mm with 1.2 mm wall thickness | |
| Stair step sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 25 mm X 25 mm with 1.2 mm wall thickness | |
| Material of mattress panel | Plywood | |
| Thickness of mattress panel | 12 mm Ply, 18 mm Ply, 20 gauge CRCA Steel sheet | |
| Upper bed support rail sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 50 mm X 25 mm with 1.2 mm wall thickness | |
| Head board sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 50 mm X 25 mm and 25 mm X 25 mm with 1.2 mm wall thickness | |
| Tail board sections (tolerance ± 2 mm excluding wall thickness) | Tube of size 50 mm X 25 mm and 25 mm X 25 mm with 1.2 mm wall thickness | |
| Colour & Finish | Paint /Finish of Metal parts | Powder Coating |
| Finish of head board / Tail board | Powder Coating | |
| Min Powder/paint coating thickness (Micron) | 50 microns | |
| Colour of bed (Metal Frame) | As per Buyer Choice | |
| Certification & Warranty | Warranty period | 1, 2, 3, 4, 5 Or higher |
© 2025 GeM All rights reserved
Site operated and maintained by Managed Service Provider
New on GeM
