menu
GeM Logo, Government of India
gem gem
GeM Logo, Government of India
categories

Catalogue values for Online UPS (V2)

Category Specification Bid Requirement (Allowed Values)
Generic Rating in KVA 80.0 KVA
Switching Technology IGBT-PWM
Input Voltage AC Three phase 300 V - 450V sinewave 50Hz
Output Voltage AC 3 phase 415V having a variable setting the range starting from 380 volt - variable upto to 415 volt.
Warranty for UPS (Years) 1, 2, 3, 4, 5 Or higher
Battery/Backup Bank Battery/Backup Bank Provided with Online UPS ( Hint: In case the UPS is supplied with battery, seller shall ensure compliance to the GST Rates as per recommendations made in the 45th Meeting of GST council dated 17th Sep 2021 ) With Battery
Type of Battery (hint: NA in case Battery not provided) SMF-VRLA conforming to JISC:8702(Pt.I,II&III), Stationary Lead Acid Batteries (with tubular positive plates) in monobloc container conforming to IS:13369:1992 latest
Backup time (Minutes) (hint: NA in case battery not provided) 30 Minutes
Minimum Guaranteed VAH 1600 X Per KVA X Per hour of backup time
Warranty for battery (Years) by Battery Manufucaturer/Brand hint: NA in case battery not provided 2, 3 Or higher
Installation and Commissioning or Service Installation and Commissioning ( Covered in the Scope of Supply) Provided
After sales service ( Turn Around Time) Within 24 hours, Within 48 hours, Within 7 days, NA
Performance / Functional Inbuilt isolation transformer With, Without
Overall Efficiency (%) >/=90% & <94% without Inbuilt isolation transformer
Overload limit 20% Overload for minimum 10 minute, 20% Overload for minimum 5 minute, 50% Overload for minimum 1 minute, 50% Overload for minimum 3 seconds
Other Functional Features Noise level (1 meter distance from UPS) should be less than 70dB, Input power factor at full output load leading to unity with active power factor correction (APFC) >/=0.92, Transient response time (for 100% load change, output must remain within +/-1% and recovery) as <20 milliseconds, Battery recharge time (after complete discharge to 90% charge) and charge rating: Battery recharge time to 90% charge after 100% DoD : 8 to 10 Hours, Maximum overshoot and Under shoot of output rated voltage (in percentage) (4%), Voltage Regulation from no load to full load (%) (< / = 2%), UPS input power factor better than 0.95 (at rated voltage)
Accessories Accessories Rack for Batteries, SNMP Card ( with Suitable Software ) for communication, The UPS shall be complete with Trolley for battery bank,battery, Cables and connectors etc
Salient Features Protection Protection for under voltage at battery terminal, Protection of Over voltage, Short Circuit & over load at UPS output terminal, Over temperature protection
Metering Input Voltage, Output Voltage, Input Frequency, Output Frequency
Alarms and Indications Indicator for Mains presence, Indicator for Battery charging and discharging, Indicator for Output Over Load with Audible Alarm, Indicator for Low Battery Voltage with Audible Alarm, Alarm for Over temperature, Alarm for Low Battery
Additional Features Pure Sinewave AC Output
Design / Construction Type of Design / Construction Floor Standing
Enclosure (mm) 1.2 mm Minimum Thickness of M.S. Sheet duly powder coated
Degree of Protection IP21, IP20 Or higher
Other Constructional Features Mains ON/OFF MCB, Battery ON/OFF MCB, Battery Fuse, Inverter reset push button, Static by pass facility, Manual by pass facility, Expandable rack facility, Shall be complete with rack rail kit for mounting of UPS in the rack and shall be housed in rugged enclosure made of steel sheet having 1.2 mm (minimum) thickness, aesthetically finished,duly pretreated and powder coated, UPS shall be free from workmanship defects, sharp edges, nicks, scratches, burst, etc. All fasteners shall be fixed properly. The equipment shall be complete with all parts and all parts shall be functional, 1 + 1 parallel redundant configuration facility on Rack mountable UPS UPS shall supply output power and charging current at the same time, NA
Operating Conditions Relative Humidity Non Condensing at 40 deg C 90, 95 Or higher
Buyer Specific Requirement Environmental Test Report Requirements Damp Heat Test : in accordance with IS:9000(part 5/sec.2)1981 at Temperature of 40 degree C
Battery Test Report Type Test Report as per relevant governing specifications from Govt Lab/NABL accredited lab
Reports And Certification Type of lab which carried out Test of Complete Product to prove the conformity of product as per specification NABL accredited lab
Agree to provide all relevant documents Test Reports/supporting document /reports etc to the buyer at the time of bidding or on demand Yes